Used Listings
Heavy Gauge Cut-To-Length Line
- Specs
- .530" -.135" without light gauge leveler
- .530" -.060" with light gauge leveler
- 96.00" Max Width
- 60,000.00 Max Coil Weight
- 65000PSI at .530" Yield Strength
- Coil Car (Remanufactured)
- Uncoiler (Remanufactured)
- Snubber (New)
- Peeler (New)
- 9 Roll Flattener (Remanufactured)
- 19 Roll Leveler (new or optional)
- Hydro-Mechanical Shear(Remanufactured)
- 20' Stacker (New)
- 40' End Exit Conveyor (New)
- Electrical Equipment (New)
- HPU
Heavy Gauge Cut-To-Length Line
- Specs
Specs
Thickness: .530" max .125"min
Width: Up to 96"
Dedicated Hydraulic Unit
Adjustable Blade Clearance
Summary of Rebuild
The Shear was completely disassembled, inspected, cleaned, painted, and reassembled.
All expendables were removed, cleaned, inspected, and new ones were installed.
Hydraulic lines replaced and fitted
Performance tested
Cut-To-Length Line
- Specs
- 4 Coil Turnstile
- Coil Car with Self Contained Power Unit
- Single Mandrel Uncoiler
- 4 Roll Coil Breaker
- 17 Roll Leveler "Bradfoote" Gearbox (Updated 2007)
- The Work Rolls are 3.5" Diameter
- Back-Up Rolls 6" Diameter
- Crop Shear
- Loop Pit Table
- Down Cut Shear (Updated 2008)
- 40' Stacker with Chain Conveyor
- Side Discharge with Hydraulic Lift Table
- 18' Side Discharge Chain Conveyor
- Updated to Falcon Operating System (2010 - by CMC)
- Updated OEM leveler controls in 2011
- Can Be Inspected Under Power
- Terms As Is/Where Is
"Like New" 9 Roll Leveler
Includes:
Motors by Buyer
Qty. 2 Gear Reducers
Drive Shafts
Distribution Gearbox
Qty. 3 Adjustable Flights of Back-up Rolls
Motors by Buyer
Qty. 2 Gear Reducers
Drive Shafts
Distribution Gearbox
Qty. 3 Adjustable Flights of Back-up Rolls
Summary of Rebuild
The 9 Roll Leveler will be completely disassembled, inspected, cleaned, painted, and reassembled.
All Work Roll Bearings and Back-up Roll Bearings were removed, cleaned, inspected, and new ones were installed.
The 4-35 Ton top screw jack and the 3 bottom screw jacks were taken apart, cleaned and inspected. During the reassembly, the screw jacks were resealed and packed with grease.
The motors and gearboxes were cleaned, inspected, and repainted.
The 9 Roll Leveler will be completely disassembled, inspected, cleaned, painted, and reassembled.
All Work Roll Bearings and Back-up Roll Bearings were removed, cleaned, inspected, and new ones were installed.
The 4-35 Ton top screw jack and the 3 bottom screw jacks were taken apart, cleaned and inspected. During the reassembly, the screw jacks were resealed and packed with grease.
The motors and gearboxes were cleaned, inspected, and repainted.
Temper Mill
Specs:
COIL WEIGHT CAPACITY: 40ton
GAUGE RANGE: .048 to .500 thick
WIDTH: 72"
ENTRY COIL ID: 24" to 36"
EXIT COIL ID: 24" x 30"
COIL OD: 80"
SPEED: Max 1200 FPM
CONTROLS DC DIGITAL SOLID STATE AND AUTOMATIC GAUGE CONTROL AGC
PLC MANUFACTURED AND DESIGNED BY I2S NEW IN 2005
CONSISTING OF:
DOUBLE STUB UNCOILER
DC DRAG GENERATOR FOR DYNAMIC BRAKING
700 HP DC
PEELER
ENTRY CROP SHEAR
UNITED MILL
27" x 30" POST AREA
MORGOIL OIL FILM BEARING WITH CIRCULATING SYSTEM
HYDRAULIC SCREW DOWNS
2 - 1000HP DC MOTORS
HYDRAULIC ROLL CHANGE SLED
STAND WEIGHT: 120 TONS
EXIT CROP SHEAR
RECOILER
24" DIAMETER EXIT DRUM
2 - 750 HP DC MOTORS
COIL WEIGHT CAPACITY: 40ton
GAUGE RANGE: .048 to .500 thick
WIDTH: 72"
ENTRY COIL ID: 24" to 36"
EXIT COIL ID: 24" x 30"
COIL OD: 80"
SPEED: Max 1200 FPM
CONTROLS DC DIGITAL SOLID STATE AND AUTOMATIC GAUGE CONTROL AGC
PLC MANUFACTURED AND DESIGNED BY I2S NEW IN 2005
CONSISTING OF:
DOUBLE STUB UNCOILER
DC DRAG GENERATOR FOR DYNAMIC BRAKING
700 HP DC
PEELER
ENTRY CROP SHEAR
UNITED MILL
27" x 30" POST AREA
MORGOIL OIL FILM BEARING WITH CIRCULATING SYSTEM
HYDRAULIC SCREW DOWNS
2 - 1000HP DC MOTORS
HYDRAULIC ROLL CHANGE SLED
STAND WEIGHT: 120 TONS
EXIT CROP SHEAR
RECOILER
24" DIAMETER EXIT DRUM
2 - 750 HP DC MOTORS
© COPYRIGHT BY DELTA 2013